Flammable Gas Sensor MQ9 (Analog/Digital)
MQ-9 gas sensor has high sensitity to Carbon Monoxide, Methane and LPG. The sensor could be used to detect different gases contains CO and combustible gases, it is with low cost and suitable for different application.
The sensitivity of the sensor can be adjusted by using the potentiometer.
EGP90.00
Features
- Support both the output digital value and the output analog value.
- Good sensitivity to CO/Combustible Gas.
- High sensitivity to Methane, Propane, and CO.
- Long life and low cost
- Pin Connection: GND: Ground, Dout: digital output, Aout: analog output Vcc: 5V
- Simple drive circuit.
Related Products
This water PH sensor is high quality, high precession, industrial standard water PH sensor. It is designed to be used in industrial applications such as water treatment facilities, rivers, lakes, peverage industry. The PH sensor equipped with 2 meter low noise cable. It is designed for low power consumption, long life and high measurement stability,
PH is a measure of acidity or alkalinity of a solution. It is commonly used to measure the quality of the water or for water monitoring. The pH scale ranges from 0 to 14.
The measurement of dissolved carbon dioxide in water is one of the most important parameters in the field of aquaculture and in industry. So, this Carbon Dioxide (CO2) sensor probe allows the measurement of dissolved carbon dioxide directly in the water and soil. It can measure the Carbon Dioxide (CO2) concentration with high accuracy with large measuring range up to 5000 ppm. The CO2 probe has an analog both RS485 and TTL output for connection to your acquisition system.
You simply need to immerse the CO2 probe directly into the environment you want to monitor, whether it’s a fish farm pond, a lake, the open sea, in a bioreactor, or a manufacturing process. The sensor then provides a continuous measurement of the partial pressure of dissolved CO2 in water.
The MQ7 is a simple-to-use Carbon Monoxide (CO) sensor suitable for sensing CO concentrations in the air. It can detect CO-gas concentrations anywhere from 20 to 2000ppm. MQ7 is a high sensitivity to carbon monoxide and stable and long-life span.
MQ-4 Sensor is highly sensitive to Methane – CH4.
Using a MQ sensor and detecting the gas is quite easy. You can either use the digital pin or the analog pin to accomplish this. Simply power the module with 5V and you should notice the power LED on the module to glow and when no gas is detected the output LED will remain turned off meaning the digital output pin will be 0V.
The Chirp! Plant Watering Alarm is a new device from wemakethings that helps extend the life of your plant by reminding you to water it. This plant water alarm is essentialy a moisture sensor with built-in coin battery and sound alarm. Chirp is a plant watering alarm – as simple as that. You put it into the soil near a plant and it emits a tiny chirp (sharp sound) when the soil is dry, reminding you to water the plant. Alternatively, Chirp can work as an I2C soil moisture sensor.
This smoke sensor module with MQ2 Smoke sensor have both digital and analog outputs , you also can adjust the sensitivity with the potentioneter.
This is an economical oxygen sensor to measure oxygen concentration (percentage) and gas Volumetric Flow Rate. The sensor measures the gas temperature also. The Oxygen sensor in home and medical oxygen generator, PSA oxygen generator, anesthesia monitors, medical ventilator, breathing equipment, oxygen analyzer, hospitals, laboratories, combustion and environmental applications.![]()
Â
Ultrasonic oxygen sensor is the latest small volume gas
It uses the ultrasonic principle to detect the oxygen concentration and flow rate in the output gas of The oxygen generator, and outputs the detection result with UART digital.
Water flow sensor consists of a plastic valve body, a water rotor, and a hall-effect sensor. When water flows through the rotor, rotor rolls. Its speed changes with different rate of flow. The hall-effect sensor outputs the corresponding pulse Signal. Can be used with ardduino
The VOC (volatile organic concentration) gas sensor is mainly used to detect and measure the concentration of VOC gases such as: Formaldehyde, Acetone. Acetic Acid, Benzene, Toluene, xylene, Butanal, Carbon Disulfide, Methylene Chloride.
The sensor module is based on MS1100 sensor which is semiconductor type sensor product widely used in ventilation equipment, ventilation fans, air filters, hoods, home appliances and other equipment. With high sensitivity and stability, it can detect more than 0.1ppm concentration of VOC gases in air.
TDS (Total Dissolved Solids) measures how many milligrams of soluble solids dissolved in one liter of water. The measure is expressed in PPM (part per million). In general, the higher the TDS value, the more soluble solids dissolved in water, and the less clean the water is. Therefore, the TDS value can be used as one of the references for reflecting the cleanliness of water.
Thanks to this product, it becomes possible to create your own measurement, collection and data transmission system. It is even possible to use this information to automate water treatment cycles. The TDS probe is waterproof; it can be immersed in water for long time measurement. However, the signal transmitter board is not waterproof.
This environmental sensor module is based on BME680 powerful environmental sensor. It can sense temperature, barometric pressure, humidity and VOC (volatile organic compound) gas of the surrounding environment.
You can monitor 4 environmental parameters simultaneously. All the measurements can be read through either I2C or SPI connection. With the BME680 you can monitor the air quality, surrounding air status, industrial pollution and controlled farming environment. Applications is not limited to weather forecasting, HVAC, home automation, fire protection systems, hazards storage area monitoring and medical space environment watching.
This is an high flow oxygen sensor to measure oxygen concentration (percentage) and gas Volumetric Flow Rate. The sensor measures the gas temperature also. The Oxygen sensor in home and medical oxygen generator, PSA oxygen generator, anesthesia monitors, medical ventilator, breathing equipment, oxygen analyzer, hospitals, laboratories, combustion and environmental applications.
The Oxygen sensor output oxygen concentration, flow rate and temperature digital data through serial UART. This make it it easy to receive data and handle it using Arduino, microcontroller or pc interface.
The oxygen sensor uses the ultrasonic velocity difference between upstream and downstream to measure oxygen concentration. This cutting edge ultrasonic technology enables small size, stable, high accuracy, low cost sensor module, long life span (>5 years). In addition, there is no need foe routine calibration.
