Flammable Gas Sensor MQ9 (Analog/Digital)
MQ-9 gas sensor has high sensitity to Carbon Monoxide, Methane and LPG. The sensor could be used to detect different gases contains CO and combustible gases, it is with low cost and suitable for different application.
The sensitivity of the sensor can be adjusted by using the potentiometer.
EGP90.00
Features
- Support both the output digital value and the output analog value.
- Good sensitivity to CO/Combustible Gas.
- High sensitivity to Methane, Propane, and CO.
- Long life and low cost
- Pin Connection: GND: Ground, Dout: digital output, Aout: analog output Vcc: 5V
- Simple drive circuit.
Related Products
Water flow sensor consists of a plastic valve body, a water rotor, and a hall-effect sensor. When water flows through the rotor, rotor rolls. Its speed changes with different rate of flow. The hall-effect sensor outputs the corresponding pulse Signal. Can be used with ardduino
This water PH sensor is high quality, high precession, industrial standard water PH sensor. It is designed to be used in industrial applications such as water treatment facilities, rivers, lakes, peverage industry. The PH sensor equipped with 2 meter low noise cable. It is designed for low power consumption, long life and high measurement stability,
PH is a measure of acidity or alkalinity of a solution. It is commonly used to measure the quality of the water or for water monitoring. The pH scale ranges from 0 to 14.
TDS (Total Dissolved Solids) measures how many milligrams of soluble solids dissolved in one liter of water. The measure is expressed in PPM (part per million). In general, the higher the TDS value, the more soluble solids dissolved in water, and the less clean the water is. Therefore, the TDS value can be used as one of the references for reflecting the cleanliness of water.
Thanks to this product, it becomes possible to create your own measurement, collection and data transmission system. It is even possible to use this information to automate water treatment cycles. The TDS probe is waterproof; it can be immersed in water for long time measurement. However, the signal transmitter board is not waterproof.
MQ-4 Sensor is highly sensitive to Methane – CH4.
Using a MQ sensor and detecting the gas is quite easy. You can either use the digital pin or the analog pin to accomplish this. Simply power the module with 5V and you should notice the power LED on the module to glow and when no gas is detected the output LED will remain turned off meaning the digital output pin will be 0V.
The MQ7 is a simple-to-use Carbon Monoxide (CO) sensor suitable for sensing CO concentrations in the air. It can detect CO-gas concentrations anywhere from 20 to 2000ppm. MQ7 is a high sensitivity to carbon monoxide and stable and long-life span.
The Chirp! Plant Watering Alarm is a new device from wemakethings that helps extend the life of your plant by reminding you to water it. This plant water alarm is essentialy a moisture sensor with built-in coin battery and sound alarm. Chirp is a plant watering alarm – as simple as that. You put it into the soil near a plant and it emits a tiny chirp (sharp sound) when the soil is dry, reminding you to water the plant. Alternatively, Chirp can work as an I2C soil moisture sensor.
The VOC (volatile organic concentration) gas sensor is mainly used to detect and measure the concentration of VOC gases such as: Formaldehyde, Acetone. Acetic Acid, Benzene, Toluene, xylene, Butanal, Carbon Disulfide, Methylene Chloride.
The sensor module is based on MS1100 sensor which is semiconductor type sensor product widely used in ventilation equipment, ventilation fans, air filters, hoods, home appliances and other equipment. With high sensitivity and stability, it can detect more than 0.1ppm concentration of VOC gases in air.
The analog gas sensor – MQ3 is suitable for detecting alcohol, this sensor can be used in a Breathalyser. It has a high sensitivity to alcohol and small sensitivity to Benzine. The sensitivity can be adjusted by the potentiometer.
Non-contact liquid level sensor can be used to provide external monitoring in liquid non-metallic material tubes, pipes and tanks such as plastic, glass, fiber-glass and ceramics. The thickness of the tube/pipe/tank/container should be less than 10mm. It is easy to use as a led is on when the liquid level reached and voltage is detected from sensor output.
The contactless liquid level sensor can be used in household appliances products, drinking and cleaning water and water treatment equipment, medical treatment and foodstuff mechanism equipment, chemical mechanism equipment and so on.
This environmental sensor module is based on BME280 powerful environmental sensor. It can sense temperature, barometric pressure, humidity .
You can monitor 2 environmental parameters simultaneously. All the measurements can be read through either I2C or SPI connection.
Water detection sensor is used to detect water leak, water level or rains. This is obtained by having a series of parallel wires exposed traces. The sensor traces have a weak pull-up resistor of 1 MΩ. The resistor will pull the sensor trace value high until a drop of water shorts the sensor trace to the grounded trace.
The analog signal output can be read directly to arduino
This is an industrial grade soil and water PH and temperature sensor. The new generation Ph sensor can measure pH and temperature level in both soil and water as well. Soil and water pH is a measure of the acidity or alkalinity of the soil or water. Soils (or water) can be classified according to their pH value where 6.5 to 7.5 is neutral soil (Ideal soil for growing plants), over 7.5is alkaline and less than 6.5 is acidic. The sensor has RS 485 serial interface with 2-meter cable which can be extended to 1000 meter without affecting measured data quality, thanks to RS 485 long distance serial communication interface. It can be integrated with GPRS/4G/WIFI/LORA wireless module.
