Flammable Gas Sensor MQ9 (Analog/Digital)
MQ-9 gas sensor has high sensitity to Carbon Monoxide, Methane and LPG. The sensor could be used to detect different gases contains CO and combustible gases, it is with low cost and suitable for different application.
The sensitivity of the sensor can be adjusted by using the potentiometer.
EGP90.00
Features
- Support both the output digital value and the output analog value.
- Good sensitivity to CO/Combustible Gas.
- High sensitivity to Methane, Propane, and CO.
- Long life and low cost
- Pin Connection: GND: Ground, Dout: digital output, Aout: analog output Vcc: 5V
- Simple drive circuit.
Related Products
A soil moisture sensor can read the amount of moisture present in the soil surrounding it. It is ideal for monitoring garden, or your plant’s water level. This is a must have tool for a connected garden.
This sensor uses the two probes to pass current through the soil, and then it reads that resistance to get the moisture level. More water makes the soil conduct electricity more easily (less resistance), while dry soil conducts electricity poorly (more resistance).
It will be helpful to remind you to water your indoor plants or to monitor the soil moisture in your garden. The IO Expansion Shield is the perfect shield to connect this senor to Arduino.
The new soil moisture sensor uses Immersion Gold which protects the nickel from oxidation.
Non-contact liquid level sensor can be used to provide external monitoring in liquid non-metallic material tubes, pipes and tanks such as plastic, glass, fiber-glass and ceramics. The thickness of the tube/pipe/tank/container should be less than 10mm. It is easy to use as a led is on when the liquid level reached and voltage is detected from sensor output.
The contactless liquid level sensor can be used in household appliances products, drinking and cleaning water and water treatment equipment, medical treatment and foodstuff mechanism equipment, chemical mechanism equipment and so on.
This environmental sensor module is based on BME280 powerful environmental sensor. It can sense temperature, barometric pressure, humidity .
You can monitor 2 environmental parameters simultaneously. All the measurements can be read through either I2C or SPI connection.
The MQ-135 gas sensor senses gases like ammonia nitrogen, oxygen, alcohols, aromatic compounds, sulfide, and smoke.
The boost converter of the chip MQ-3 gas sensor is PT1301. The operating voltage of this gas sensor is from 2.5V to 5.0V. The MQ-3 gas sensor has a lower conductivity to clean the air as a gas sensing material. In the atmosphere, we can find polluting gases, but the conductivity of the gas sensor increases as the concentration of polluting gas increases. MQ-135 gas sensor can be implemented to detect the smoke, benzene, steam, and other harmful gases. It has the potential to detect different harmful gases. The MQ-135 gas sensor is a low co st to purchase.
This 4 in 1 water quality sensor is a high quality industrial standard sensor that can measure EC (conductivity), TDS (total dissolved solids), Salinity and water temperature. This sensor enjoy high precision, long life and high stability in measurements. The sensor has RS 485 serial interface with 2-meter cable which can be extended to 1000 meter without affecting measured data quality, thanks to RS 485 long distance serial communication interface. It can be integrated with GPRS/4G/WIFI/LORA wireless module. Â
Conductivity (EC) is a measure of the ability of water to pass an electric current; it is affected by the presence of dissolved solids such as chloride, nitrate and phosphate. Conductivity can be a very useful indicator that a discharge of some sort has entered a stream, or some other change has occurred. TDS Sensor detects the Total Dissolved Solids (TDS) levels in the water which can be used to indicate the water quality. The Salinity Sensor easily and precisely measures the total dissolved salt content in an aqueous solution.Â
The VOC (volatile organic concentration) gas sensor is mainly used to detect and measure the concentration of VOC gases such as: Formaldehyde, Acetone. Acetic Acid, Benzene, Toluene, xylene, Butanal, Carbon Disulfide, Methylene Chloride.
The sensor module is based on MS1100 sensor which is semiconductor type sensor product widely used in ventilation equipment, ventilation fans, air filters, hoods, home appliances and other equipment. With high sensitivity and stability, it can detect more than 0.1ppm concentration of VOC gases in air.
The measurement of dissolved carbon dioxide in water is one of the most important parameters in the field of aquaculture and in industry. So, this Carbon Dioxide (CO2) sensor probe allows the measurement of dissolved carbon dioxide directly in the water and soil. It can measure the Carbon Dioxide (CO2) concentration with high accuracy with large measuring range up to 5000 ppm. The CO2 probe has an analog both RS485 and TTL output for connection to your acquisition system.
You simply need to immerse the CO2 probe directly into the environment you want to monitor, whether it’s a fish farm pond, a lake, the open sea, in a bioreactor, or a manufacturing process. The sensor then provides a continuous measurement of the partial pressure of dissolved CO2 in water.
Sensitive material of MQ-5 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exist, The sensors conductivity is more higher along with the gas concentration rising. The sensor convert change of conductivity to correspond output signal of gas concentration.
MQ-5 gas sensor has high sensitity to Methane, Propane and Butane, ch4 and natural gas.
This sensor has a high sensitivity and fast response time. It is suitable for sensing hydrogen concentrations in the air. The MQ-8 can detect hydrogen gas concentrations anywhere from 100-10000ppm.
The sensor can output an analog or digital signal. The sensitivity can be adjusted by the potentiometer.
They are used in gas leakage detecting equipments in home and industry applications.
This is an economical oxygen sensor to measure oxygen concentration (percentage) and gas Volumetric Flow Rate. The sensor measures the gas temperature also. The Oxygen sensor in home and medical oxygen generator, PSA oxygen generator, anesthesia monitors, medical ventilator, breathing equipment, oxygen analyzer, hospitals, laboratories, combustion and environmental applications.![]()
Â
Ultrasonic oxygen sensor is the latest small volume gas
It uses the ultrasonic principle to detect the oxygen concentration and flow rate in the output gas of The oxygen generator, and outputs the detection result with UART digital.
MQ-4 Sensor is highly sensitive to Methane – CH4.
Using a MQ sensor and detecting the gas is quite easy. You can either use the digital pin or the analog pin to accomplish this. Simply power the module with 5V and you should notice the power LED on the module to glow and when no gas is detected the output LED will remain turned off meaning the digital output pin will be 0V.
Water flow sensor consists of a plastic valve body, a water rotor, and a hall-effect sensor. When water flows through the rotor, rotor rolls. Its speed changes with different rate of flow. The hall-effect sensor outputs the corresponding pulse Signal. Can be used with ardduino
