Oxygen Concentration and Flow Rate with LCD DISPLAY
This is an high flow oxygen sensor to measure oxygen concentration (percentage) and gas Volumetric Flow Rate. The sensor measures the gas temperature also. The Oxygen sensor in home and medical oxygen generator, PSA oxygen generator, anesthesia monitors, medical ventilator, breathing equipment, oxygen analyzer, hospitals, laboratories, combustion and environmental applications.
The Oxygen sensor output oxygen concentration, flow rate and temperature digital data through serial UART. This make it it easy to receive data and handle it using Arduino, microcontroller or pc interface.
The oxygen sensor uses the ultrasonic velocity difference between upstream and downstream to measure oxygen concentration. This cutting edge ultrasonic technology enables small size, stable, high accuracy, low cost sensor module, long life span (>5 years). In addition, there is no need foe routine calibration.
EGP3,800.00
Features
- Voltage supply: DC 3.3 – 5 voltÂ
- 3F260Â
- Concentration detection accuracy: ±1.%  @(25 ± 2)°C ± 2% @(5~60)°C
- Gas flow detection range: 0~ 260 L/min
- Flow detection accuracy: ±0.3 L/min @(25 ± 2)°C
- Detection period: 1s
- Digital Output: 9600bps UART 5V TTLÂ
- Working temperature: 5～60°C
- Maximum pressure: 150 kPa
- Dimensions: 120.5mm x 29.5mm x 22mm (L x W x H)
- Sensor weight: 25 gm
Related Products
MQ-4 Sensor is highly sensitive to Methane – CH4.
Using a MQ sensor and detecting the gas is quite easy. You can either use the digital pin or the analog pin to accomplish this. Simply power the module with 5V and you should notice the power LED on the module to glow and when no gas is detected the output LED will remain turned off meaning the digital output pin will be 0V.
Water flow sensor consists of a plastic valve body, a water rotor, and a hall-effect sensor. When water flows through the rotor, rotor rolls. Its speed changes with different rate of flow. The hall-effect sensor outputs the corresponding pulse Signal. Can be used with ardduino
Gravity: Analog pH Sensor / Meter Pro Kit V2 For Arduino is a professional Arduino pH Sensor Meter Kit with an industrial electrode. This ph. sensor module is an upgrade for V1 with improvement is calibration method, more friendly use and better accuracy
This is an economical oxygen sensor to measure oxygen concentration (percentage) and gas Volumetric Flow Rate. The sensor measures the gas temperature also. The Oxygen sensor in home and medical oxygen generator, PSA oxygen generator, anesthesia monitors, medical ventilator, breathing equipment, oxygen analyzer, hospitals, laboratories, combustion and environmental applications.
The Oxygen sensor output oxygen concentration, flow rate and temperature digital data through serial UART. This make it it easy to receive data and handle it using arduio, microcontroller or pc interface.
The oxygen sensor uses the ultrasonic velocity difference between upstream and downstream to measure oxygen concentration. This cutting edge ultrasonic technology enables small size, stable, high accuracy, low cost sensor module, long life span (>5 years). In addition, there is no need foe routine calibration.
This 4 in 1 water quality sensor is a high quality industrial standard sensor that can measure EC (conductivity), TDS (total dissolved solids), Salinity and water temperature. This sensor enjoy high precision, long life and high stability in measurements. The sensor has RS 485 serial interface with 2-meter cable which can be extended to 1000 meter without affecting measured data quality, thanks to RS 485 long distance serial communication interface. It can be integrated with GPRS/4G/WIFI/LORA wireless module. Â
Conductivity (EC) is a measure of the ability of water to pass an electric current; it is affected by the presence of dissolved solids such as chloride, nitrate and phosphate. Conductivity can be a very useful indicator that a discharge of some sort has entered a stream, or some other change has occurred. TDS Sensor detects the Total Dissolved Solids (TDS) levels in the water which can be used to indicate the water quality. The Salinity Sensor easily and precisely measures the total dissolved salt content in an aqueous solution.Â
Water detection sensor is used to detect water leak, water level or rains. This is obtained by having a series of parallel wires exposed traces. The sensor traces have a weak pull-up resistor of 1 MΩ. The resistor will pull the sensor trace value high until a drop of water shorts the sensor trace to the grounded trace.
The analog signal output can be read directly to arduino
MQ-9 gas sensor has high sensitity to Carbon Monoxide, Methane and LPG. The sensor could be used to detect different gases contains CO and combustible gases, it is with low cost and suitable for different application.
The sensitivity of the sensor can be adjusted by using the potentiometer.
This sensor has a high sensitivity and fast response time. It is suitable for sensing hydrogen concentrations in the air. The MQ-8 can detect hydrogen gas concentrations anywhere from 100-10000ppm.
The sensor can output an analog or digital signal. The sensitivity can be adjusted by the potentiometer.
They are used in gas leakage detecting equipments in home and industry applications.
The MQ-6 Gas sensor can detect or measure gases like LPG, methane and butane. The MQ-6 sensor module comes with a Digital Pin which makes this sensor to operate even without a microcontroller and that comes in handy when you are only trying to detect one particular gas. When it comes to measuring the gas in ppm the analog pin has to be used, the analog pin also TTL driven and works on 5V and hence can be used with most common microcontrollers.
So if you are looking for a sensor to detect or measure gasses like LPG, butane or methane with or without a microcontroller then this sensor might be the right choice for you.
This environmental sensor module is based on BME680 powerful environmental sensor. It can sense temperature, barometric pressure, humidity and VOC (volatile organic compound) gas of the surrounding environment.
You can monitor 4 environmental parameters simultaneously. All the measurements can be read through either I2C or SPI connection. With the BME680 you can monitor the air quality, surrounding air status, industrial pollution and controlled farming environment. Applications is not limited to weather forecasting, HVAC, home automation, fire protection systems, hazards storage area monitoring and medical space environment watching.
This is 4 in 1 water and soil sensor. The new generation sensor can be used for Ec, moisture, salinity and temperature measurements in both water and soil media as well. This sensor is a high quality Anti-corrosion, stainless steel industrial standard sensor that can measure soil and water EC (conductivity), soil and water moisture contents, Salinity and temperature. This sensor enjoys high precision, long life and high stability in measurements. The sensor has RS 485 serial interface with 2-meter cable which can be extended to 1000 meter without affecting measured data quality, thanks to RS 485 long distance serial communication interface. It can be integrated with GPRS/4G/WIFI/LORA wireless module.
The analog gas sensor – MQ3 is suitable for detecting alcohol, this sensor can be used in a Breathalyser. It has a high sensitivity to alcohol and small sensitivity to Benzine. The sensitivity can be adjusted by the potentiometer.
