Soil NPK Sensor (Nitrogen-Phosphorus-Potassium) Fertility & Nutrient Measurements
The soil nutrient content can be easily measured using NPK Soil Sensor. Measurement of soil content N (nitrogen), P (phosphorus), and K (potassium) is necessary to determine how much additional nutrient content is to be added to soil to increase crop fertility.
The soil fertility is detected using NPK sensors. A major component of soil fertilizer is nitrogen, phosphorus, and potassium. The knowledge of the soil nutrient concentration can help us to learn about nutritional deficiency or abundance in soils used to endorse plant production.
This Soil NPK sensor is a low cost, quick responsive, high precision & portable Sensor that works with Modbus RS485. The advantage of this sensor over a traditional detection method is that it gives very fast measurement & data are highly accurate. All you need is to insert its probe in soil and get the reading using your MCU (Arduino, Tiva C, Raspberry, Personal computer).
EGP3,900.00
Features
- Supply Voltage:Â 5 – 30V
- Measurements Range: 1-999 mg/Kg
- Measurements Accuracy: 1 mg/Kg
- Output Signal:Â Â RS485
- Protection : IP68
- Response Time : ≤ 1 sec
Related Products
This smoke sensor module with MQ2 Smoke sensor have both digital and analog outputs , you also can adjust the sensitivity with the potentioneter.
MQ-4 Sensor is highly sensitive to Methane – CH4.
Using a MQ sensor and detecting the gas is quite easy. You can either use the digital pin or the analog pin to accomplish this. Simply power the module with 5V and you should notice the power LED on the module to glow and when no gas is detected the output LED will remain turned off meaning the digital output pin will be 0V.
A soil moisture sensor can read the amount of moisture present in the soil surrounding it. It is ideal for monitoring garden, or your plant’s water level. This is a must have tool for a connected garden.
This new type capacitive soil humidity sensor differs from other resistive sensors, adopting capacitive sensing principle to detect soil humidity. Since the circuit is not exposed at the detected end, the corrosion problem of sensor is avoided, increasing the sensor operating life and measurments accuracy.
The built-in chip supports 3.3~5.5V working environment, Arduino, ESP32, micro:bit and controller. As to mini PC, you need an ADC module (analog signals are converted into signals).
MQ-9 gas sensor has high sensitity to Carbon Monoxide, Methane and LPG. The sensor could be used to detect different gases contains CO and combustible gases, it is with low cost and suitable for different application.
The sensitivity of the sensor can be adjusted by using the potentiometer.
This is an industrial grade soil and water PH and temperature sensor. The new generation Ph sensor can measure pH and temperature level in both soil and water as well. Soil and water pH is a measure of the acidity or alkalinity of the soil or water. Soils (or water) can be classified according to their pH value where 6.5 to 7.5 is neutral soil (Ideal soil for growing plants), over 7.5is alkaline and less than 6.5 is acidic. The sensor has RS 485 serial interface with 2-meter cable which can be extended to 1000 meter without affecting measured data quality, thanks to RS 485 long distance serial communication interface. It can be integrated with GPRS/4G/WIFI/LORA wireless module.
The analog gas sensor – MQ3 is suitable for detecting alcohol, this sensor can be used in a Breathalyser. It has a high sensitivity to alcohol and small sensitivity to Benzine. The sensitivity can be adjusted by the potentiometer.
Gravity: Analog pH Sensor / Meter Pro Kit V2 For Arduino is a professional Arduino pH Sensor Meter Kit with an industrial electrode. This ph. sensor module is an upgrade for V1 with improvement is calibration method, more friendly use and better accuracy
This environmental sensor module is based on BME680 powerful environmental sensor. It can sense temperature, barometric pressure, humidity and VOC (volatile organic compound) gas of the surrounding environment.
You can monitor 4 environmental parameters simultaneously. All the measurements can be read through either I2C or SPI connection. With the BME680 you can monitor the air quality, surrounding air status, industrial pollution and controlled farming environment. Applications is not limited to weather forecasting, HVAC, home automation, fire protection systems, hazards storage area monitoring and medical space environment watching.
TDS (Total Dissolved Solids) measures how many milligrams of soluble solids dissolved in one liter of water. The measure is expressed in PPM (part per million). In general, the higher the TDS value, the more soluble solids dissolved in water, and the less clean the water is. Therefore, the TDS value can be used as one of the references for reflecting the cleanliness of water.
Thanks to this product, it becomes possible to create your own measurement, collection and data transmission system. It is even possible to use this information to automate water treatment cycles. The TDS probe is waterproof; it can be immersed in water for long time measurement. However, the signal transmitter board is not waterproof.
This is an high flow oxygen sensor to measure oxygen concentration (percentage) and gas Volumetric Flow Rate. The sensor measures the gas temperature also. The Oxygen sensor in home and medical oxygen generator, PSA oxygen generator, anesthesia monitors, medical ventilator, breathing equipment, oxygen analyzer, hospitals, laboratories, combustion and environmental applications.
The Oxygen sensor output oxygen concentration, flow rate and temperature digital data through serial UART. This make it it easy to receive data and handle it using Arduino, microcontroller or pc interface.
The oxygen sensor uses the ultrasonic velocity difference between upstream and downstream to measure oxygen concentration. This cutting edge ultrasonic technology enables small size, stable, high accuracy, low cost sensor module, long life span (>5 years). In addition, there is no need foe routine calibration.
Water flow sensor consists of a plastic valve body, a water rotor, and a hall-effect sensor. When water flows through the rotor, rotor rolls. Its speed changes with different rate of flow. The hall-effect sensor outputs the corresponding pulse Signal. Can be used with ardduino
The MQ-6 Gas sensor can detect or measure gases like LPG, methane and butane. The MQ-6 sensor module comes with a Digital Pin which makes this sensor to operate even without a microcontroller and that comes in handy when you are only trying to detect one particular gas. When it comes to measuring the gas in ppm the analog pin has to be used, the analog pin also TTL driven and works on 5V and hence can be used with most common microcontrollers.
So if you are looking for a sensor to detect or measure gasses like LPG, butane or methane with or without a microcontroller then this sensor might be the right choice for you.
