Smoke sensor MQ2 (Digital/Analog)
This smoke sensor module with MQ2 Smoke sensor have both digital and analog outputs , you also can adjust the sensitivity with the potentioneter.
EGP95.00
PIN Connection
4 pins as follows:
- VCC Â Â (5 V)
- GND (ground)
- Aout (Analog output)
- Dout (Digital output)
When connect to arduino, use digital pins in digital mode (high or low) and use analog pins for analog mode (diffrenet value for different smoke intensity).
Related Products
The measurement of dissolved carbon dioxide in water is one of the most important parameters in the field of aquaculture and in industry. So, this Carbon Dioxide (CO2) sensor probe allows the measurement of dissolved carbon dioxide directly in the water and soil. It can measure the Carbon Dioxide (CO2) concentration with high accuracy with large measuring range up to 5000 ppm. The CO2 probe has an analog both RS485 and TTL output for connection to your acquisition system.
You simply need to immerse the CO2 probe directly into the environment you want to monitor, whether it’s a fish farm pond, a lake, the open sea, in a bioreactor, or a manufacturing process. The sensor then provides a continuous measurement of the partial pressure of dissolved CO2 in water.
Water detection sensor is used to detect water leak, water level or rains. This is obtained by having a series of parallel wires exposed traces. The sensor traces have a weak pull-up resistor of 1 MΩ. The resistor will pull the sensor trace value high until a drop of water shorts the sensor trace to the grounded trace.
The analog signal output can be read directly to arduino
This environmental sensor module is based on BME280 powerful environmental sensor. It can sense temperature, barometric pressure, humidity .
You can monitor 2 environmental parameters simultaneously. All the measurements can be read through either I2C or SPI connection.
The soil nutrient content can be easily measured using NPK Soil Sensor. Measurement of soil content N (nitrogen), P (phosphorus), and K (potassium) is necessary to determine how much additional nutrient content is to be added to soil to increase crop fertility.
The soil fertility is detected using NPK sensors. A major component of soil fertilizer is nitrogen, phosphorus, and potassium. The knowledge of the soil nutrient concentration can help us to learn about nutritional deficiency or abundance in soils used to endorse plant production.
This Soil NPK sensor is a low cost, quick responsive, high precision & portable Sensor that works with Modbus RS485. The advantage of this sensor over a traditional detection method is that it gives very fast measurement & data are highly accurate. All you need is to insert its probe in soil and get the reading using your MCU (Arduino, Tiva C, Raspberry, Personal computer).
Sensitive material of MQ-5 gas sensor is SnO2, which with lower conductivity in clean air. When the target combustible gas exist, The sensors conductivity is more higher along with the gas concentration rising. The sensor convert change of conductivity to correspond output signal of gas concentration.
MQ-5 gas sensor has high sensitity to Methane, Propane and Butane, ch4 and natural gas.
Gravity: Analog pH Sensor / Meter Pro Kit V2 For Arduino is a professional Arduino pH Sensor Meter Kit with an industrial electrode. This ph. sensor module is an upgrade for V1 with improvement is calibration method, more friendly use and better accuracy
MQ-9 gas sensor has high sensitity to Carbon Monoxide, Methane and LPG. The sensor could be used to detect different gases contains CO and combustible gases, it is with low cost and suitable for different application.
The sensitivity of the sensor can be adjusted by using the potentiometer.
The analog gas sensor – MQ3 is suitable for detecting alcohol, this sensor can be used in a Breathalyser. It has a high sensitivity to alcohol and small sensitivity to Benzine. The sensitivity can be adjusted by the potentiometer.
This is an economical oxygen sensor to measure oxygen concentration (percentage) and gas Volumetric Flow Rate. The sensor measures the gas temperature also. The Oxygen sensor in home and medical oxygen generator, PSA oxygen generator, anesthesia monitors, medical ventilator, breathing equipment, oxygen analyzer, hospitals, laboratories, combustion and environmental applications.![]()
Â
Ultrasonic oxygen sensor is the latest small volume gas
It uses the ultrasonic principle to detect the oxygen concentration and flow rate in the output gas of The oxygen generator, and outputs the detection result with UART digital.
This is an high flow oxygen sensor to measure oxygen concentration (percentage) and gas Volumetric Flow Rate. The sensor measures the gas temperature also. The Oxygen sensor in home and medical oxygen generator, PSA oxygen generator, anesthesia monitors, medical ventilator, breathing equipment, oxygen analyzer, hospitals, laboratories, combustion and environmental applications.
The Oxygen sensor output oxygen concentration, flow rate and temperature digital data through serial UART. This make it it easy to receive data and handle it using Arduino, microcontroller or pc interface.
The oxygen sensor uses the ultrasonic velocity difference between upstream and downstream to measure oxygen concentration. This cutting edge ultrasonic technology enables small size, stable, high accuracy, low cost sensor module, long life span (>5 years). In addition, there is no need foe routine calibration.
The Chirp! Plant Watering Alarm is a new device from wemakethings that helps extend the life of your plant by reminding you to water it. This plant water alarm is essentialy a moisture sensor with built-in coin battery and sound alarm. Chirp is a plant watering alarm – as simple as that. You put it into the soil near a plant and it emits a tiny chirp (sharp sound) when the soil is dry, reminding you to water the plant. Alternatively, Chirp can work as an I2C soil moisture sensor.
Water flow sensor consists of a plastic valve body, a water rotor, and a hall-effect sensor. When water flows through the rotor, rotor rolls. Its speed changes with different rate of flow. The hall-effect sensor outputs the corresponding pulse Signal. Can be used with ardduino
